Strona domowa
Opis
established in 2006,dealing in (i)cut wire shot ,which is used in shot blasting process Cut-wire shot is produced by cutting wire into lengths equal to the wire diameter. Quality is assured by control of the chemical and physical properties inherent in the wire and accurate sizing to length. Every piece is 100% solid. Cut-wire shot is available in an As-Cut (cylindrical) form as well as in a normal conditioned and special conditioned (Spherical) shape. Cut wire shot is available in sizes from 0.40mm to 2.00mm .
our Company is providing the largest range of cut wire shot in different sizes and metals , which suits the best for its customer requirements . Details of product are given as below :
PRODUCT LIST
SIZE
Grit Steel ShotCut Wire Shot (in inches)Equivalent Cut Wire Shot
G-50S-170 0.017 0.40
G-40S-190 0.020 0.50
G-40S-230 0.023 0.60
G-25S-280 0.028 0.70
G-25S-330 0.032 0.80
G-18S-360 0.035 0.90
G-18S-390 0.041 1.00
G-16S-460 0.047 1.20
G-17S-550 0.054 1.40
G-12S-660 0.062 1.60
G-10S-780 0.080 2.00
MATERIAL
MILD STEEL TYPE 1020
CARBON STEELTYPE 1070
STAINLESS STEELTYPE 302 / 304 /202 / 430
ALUMINUM
HARDNESS RANGE
1.MILD STEEL 20 HRC
2.CARBON STEEL45 - 54 / 55 - 60 HRC
3.STAINLESS STEEL 302 / 304 / 202 / 430 having 32 HRC MINIMUM
SHAPE DESCRIPTIONSPECIFICATION
AS CUT (-U) CYLINDRICAL WITH SHARP EDGEIS 5873-1970 / SAE J441
NORMAL (-C) CORNER PRE ROUNDIS 5873-1970 / SAE J441
CONDITIONED (-3C) ALMOST SPHERICALIS 5873-1970 / SAE J441
PACKING PROVIDED : 25Kgs. /Bag
APPLICATION OF CUT WIRE SHOT :
(1)Blast cleaning
Blast cleaning of die-casting, foundry pieces, forgings, sand removal, steel board, steel material, H type steel structure.
(2)Rust removal
Rust removal of foundry pieces, forgings, steel board, steel material, steel structure, descaling of forging.
(3)Shot peening
Shot peening of heat treatment pieces, gear etc.
(4)Shot blasting
Shot blasting of profile steel, steel board, steel material, ship board.
(5)Shot polishing
Shot polishing of steel board, steel material, and profile steel.
(6)Grit removal
Grit removal
(7)Pre-treatment
Pre-treatment of surface, steel structure, before-painting.
ADVANTAGES OF CUT WIRE SHOT:
1. Most economical and lowest consumption.
2. Available in various sizes as per requirement.
3. More life span, till completely reduced to smallest tiny particle.
4. Increases the fatigue life of the blasted components.
5. No possibility for dust formation during shot blasting.
6. Cleans the product faster.
7. Cuts down the maintenance cost of shot blasting machine.
8. No dust or health hazard during operation.
CUT WIRE SHOT better than CAST STEEL SHOT due to followingCHARACTER
1. Raw Material is of exact composition without any material defect (blow holes, porosity, shrinkage etc.), and wears out nominally during its use.
2. No Dust generation
.
3 environment Friendly.
4. Performance Consistency
5. Consistent Performance
6. Reduced Time for Shot Blasting/Peening
7. Consumption decreases
Timeline
{{companyName}} {{title}}
Visit our website @ {{website}}
{{companyName}} {{title}}
Our new location address: